TPS2346
 
SLUS529  MAY 2002
8
www.ti.com
functional overview (continued)
As each back-end voltage is ramped, its level is validated to ensure it is within the established UV and OV
tolerances at the expiration of a programmable time period, protecting against start-up into faulted loads. The
same capacitor at the IRAMP pin which sets the current ramp rate is also used to establish this ramp-up time
limit. If all four supplies successfully reach a known good state, the PG
 output signal is pulled low to allow
enumeration of the add-in card.
To protect the backplane power bus, the TPS2346 provides an electronic circuit breaker that trips upon detecting
an overcurrent event. The detection threshold of an overcurrent event is internally set to approximately two
times (2x) IMAX. The 5.2-V channel also includes a circuit breaker function; its trip threshold is always a
minimum of 50 mV above the current-limit sense voltage. If any channel trips the circuit breaker, all supply
outputs are rapidly turned off, and remain latched off. Also, the PG
 output becomes high-impedance. The
TPS2346 can be reset by cycling either the ENABLE
 input or power to the device.
The low, 20-mV (150 mV on the 5.2-V channel) nominal sense voltage limit allows the use of low-value sense
resistors, or for high-current applications, the use of PC board copper trace. This helps minimize the insertion
loss across the hot swap interface. Further insertion loss reduction is achieved via the on-chip charge pump,
which ensures maximum gate overdrive on each of the three external pass MOSFETs on the positive supply
channels. This feature helps users obtain lower R
DS(on)
  characteristics with their preferred N-channel
MOSFETs.
Under a normal PC board shutdown event, the TPS2346 also turns off power in a controlled manner. To initiate
a shutdown, ENABLE
 is brought to a logic high during a healthy supply state (outputs on and no faults present).
The supply outputs are then sequentially ramped off in the reverse order of the ramp-up sequence. After all
supply outputs are off, the TPS2346 goes into a low-current sleep mode.
相关PDF资料
TPS24711DGSR IC CTRLR HOT SWAP 2.5-18V 10MSOP
TPS2491DGSG4 IC POS HV HOT-SWAP CTRLR 10-MSOP
W83772G IC H/W MONITOR 8-TSSOP
W83L786G IC H/W MONITOR 28-SSOP
X96011V14IZ IC SENSOR TEMP BIAS SGL 14-TSSOP
XR4151CP-F IC CONV VF/FV 8PDIP
XRP7714ILB-0X14-F IC REG 5OUT BCK/LINEAR 40TQFN
XRP7740ILB-0X18-F IC REG 5OUT BCK/LINEAR 40TQFN
相关代理商/技术参数
TPS2350D 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2350DG4 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2350DR 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2350DRG4 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2350EVM 功能描述:电源管理IC开发工具 Telecom -48V OR-ing Diode RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS2350PW 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2350PW 制造商:Texas Instruments 功能描述:HOT SWAP CONTROLLER ((NW)) 制造商:Texas Instruments 功能描述:IC, HOT SWAP POWER MANAGER, 14-TSSOP
TPS2350PWG4 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube